#1
|
|||
|
|||
![]()
Homemade Water Injection Page
Updated with more useful info and pictures! Getting to Know Water Injection The benefits of Water Injection are substantial and well documented. A lot of people hear about the idea of injecting water into the air that enters the engine and wonder if putting water into the engine isn't a bad thing. The truth of the matter is that it's a very good thing if done properly. Only a small amount of water is injected as a fine mist. This mist is evaporated quickly in the hot intake air. As the water evaporates, it cools the intake charge significantly. Cooler intake temperatures make the engine less likely to knock. This allows the ECU to fully advance timing and extract more power. This strong cooling effect also makes the air more dense so the air mass in the cylinder can increase, which allows the fuel delivery amount to increase, which increases the power released for each turn of the engine. It's often said that water injection will allow your car on a hot day to run as well as it does on a very cold day. For turbocharged cars, this also means that the engine can be run at a higher level of boost for a given grade of gas and ambient temperature. Often, non-turbocharged or supercharged vehicles will not see much of a benefit. However, it can allow high compression normally-aspirated cars to possibly run on a lower grade of gas. Once you're convinced of the need for a water injection kit, you have to buy one. The choices go from the low-end Spearco system (which can be bought for about $160) to the high-end Aquamist systems, which start at $400 and go up into the thousands. Many people complain about the quality of the pump and the nozzles included in the Spearco system, but many people also complain about the price of the high-quality Aquamist systems. So one alternative is building a system yourself. This page will detail my efforts to build and tune my water injection system. Good additional resources are: A Merkur page with lots of good info National mailing list with links Notes on Nozzle Choice: I spoke with Brad Schaeffer at Georges Imports (816-333-6582). He's a very knowledgeable guy when it comes to water injection. Anyway, he clued me into Aquamist's web page. www.aquamist.co.uk. If you click on "supplier listing" then click on one of the green checkmarks next to a jet-nozzle on the left, a chart comes up with the flow rates for each nozzle based on supply pressure. It's listed for 5 bar and 7 bar. 5 bar is 73 psi, and 7 bar is about 102 psi. Since the pump that I'll be using oscillates from about 80 psi to 100 psi, our pump will be in the middle of those two figures. Rule of thumb: You want your water injection to be putting in about 10% to 15% of the amount of fuel injected. So, since I have 550cc injectors (times 4 injectors) want about 220 to 330 cc's of water going in (assuming I'm using 550's to their potential). This could be accomplished by going with a 0.6 to 0.8 mm nozzle. So, you should look at this chart and tell me what size you want. Brad recommended a few things: 1. He thought for our engines and setups (with 550s) that a 0.5 or 0.6 would be plenty. (Given a 100 psi pump) 2. He recommended getting a couple or three sizes to be able to test which works the best. 3. He recommended going with a two stage system. This would require 2 solenoids and 2 pressure switches. The first would come on at something like 4 psi and drive a .4 mm nozzle, and the second would come on at a higher boost (15 psi) and drive an additional .4 mm nozzle. The first nozzle is mounted 3-5" from the throttle plate. The second is mounted way upstream. Either farther down on the throttle body, farther back on the UIC pipe, or even before the intercooler. He said that once a system like this is setup up, you're car on a 90 degree day drives like it's a 20 degree day. He also runs the water injection from his normal windshield wiper reservoir. He just makes sure to use alcohol-based windshield wiper fluid. He said the small amounts of detergents in the fluid have not caused him problems. He's been doing this a long time, though mostly on Saab's. Parts List: Most all of the parts need to be able to work with the conditions found under the hood of an automobile.
![]() On the 1995 Mitsubishi Eclipse GSX, the windshield wiper reservoir is in the trunk under the spare tire. I removed the tank and was happy to see that it already has a level sensor. I drilled a hole in the top, put in a rubber grommet. I took a length of copper tubing and inserted that through the grommet. I then took some tubing, put that over the copper and further fastened it down with a zip-tie. ![]() ![]() ![]() ![]() ![]() Cold Air Intake Page |
#2
|
||||
|
||||
![]() ![]() ![]()
__________________
|
#3
|
|||
|
|||
![]() |
#4
|
|||
|
|||
![]() يا سلام علي الشغل البيتي لا يعلي عليه
|
#5
|
|||
|
|||
![]()
البيتي لا يعلي عليه
THAT'S TRUE OF SURE !!!!!!!!!!! ![]() ![]() ![]() |
![]() |
الكلمات الدليلية |
تقنية قادرة على تحويل الماء إلى وقود !, water, هيدروجين |
|
|