المشاركة الأصلية كتبت بواسطة aimooo (المشاركة 732762)

احب ابعت سلامي لكارز ادماير واحمد صادق
:waving::waving::waving:

المشاركة الأصلية كتبت بواسطة ahmed mattar (المشاركة 733615)

السلام عليكم وياريت لو ترفع صور العربية بر وجوة علشان نعرف الجديد بستمرار

المشاركة الأصلية كتبت بواسطة cars admire (المشاركة 733112)

Grease Gun Piston Pump
بمشحمة او مسدس شحم !!!!!!!!!!!
http://www.waikatobearings.co.nz/ima...20&w=250&h=500

http://www.waikatobearings.co.nz/ima...20&w=250&h=500

Grease Gun Piston Pump with Block Feeder

http://assets.academy.com/mgen/45/10...jpg?is=500,500

Lever Grease Gun

http://www.southernstates.com/catalo...e/05300130.jpg

http://www.towsure.com/images/produc...grease-gun.jpg
http://yamadalubricator.com/images/KPL-24-Drawing.gif
:fun_36_3_16[1]::waving::fun_7_5_128[1]:
http://yamadalubricator.com/images/pump.jpg
http://yamadalubricator.com/images/pump_hose.jpg
Application Example -
hose reel not included.

http://yamadalubricator.com/images/pump_mobile.jpg
Application Example -
lubrication lines not included.
see how yamada
beats lincoln

- The Industry's Most Trusted Grease Lubricator Pumps
The KPL-24 is used in conjunction with a hose reel and hand grease gun and runs on a 24 volt power source. It fits directly onto a 5 gallon grease pail offering portability, cleanliness and versatility. The KPL-24 produces high volume, high pressure lubrication with unmatched durability & reliability.
The KPL-24 has the ability to operate on just about any kind of mobile or stationary mining or construction equipment, as well as wind turbines, and has a vibration resistance of 4G for all ground equipment.
Uses of the KPL-24


The KPL-24 grease lubricator is highly versatile and can be used in combination with other equipment to meet any lubrication need.

• Stand-Alone Pump - Consists of the Yamada KPL-24 grease pump and grease gun
• Semi-Automatic Configurations - The KPL-24 can be combined with a grease feeder distributor, lubrication lines and fittings to create a semi-automatic system.
• Fully Automatic Configurations - The KPL-24 can be the driving pump behind a fully automatic system when combined with an electric monitor, grease feeder distributor, lubrication lines and fittings.
• Full Monitoring Automatic Configurations - The KPL-24 can also be combined with low level grease sensors, blockage indicators, fault warning, intelligent electronic monitor, grease feeder distributors, lubrication lines and fittings to create a fully automated and self-monitoring system.

Quick Setup Instructions

(Download Manual)

• Rock the inductor plate on top of the grease - until it almost oozes out of the sides and center hole. This will remove any trapped air.
• Stick the pump (suction tube) through the hole in the inductor plate.
• Open Needle Valve and turn on the pump. When a steady stream (unbroken) of grease comes out of the hole in the needle valve, shut off the pump. This will remove any remaining air.
• Close needle valve
• Open gun (trigger) and turn on pump.
• When a steady stream comes out, the pump is primed and ready to go.

:fun_36_3_9[1]::018A1D~146: